|
|||||||||||||||||||||||||||||||||||
|
This is our ARCHIVE site. This site contains content that was on our community site "amset.info" and is no longer maintained. However as there are large numbers of links to the content on the internet, it has been retained on this site so that people who find that information of use, can still access it. However it cannot be guaranteed to be up to date, or accurate, particularly with regards to modern best practises. Most of the content was originally written between 1998 and 2008. Image watermarks refer to the old url of amset.info, which is another domain under control of Sembee Ltd. Our Exchange Server related content can be found at http://exchange.sembee.info/ and is actively maintained. Other sites from Sembee include: dosprompt.info - loginscripts.info - office-recovery.com - wuauclt.info - statuspages.co.uk Modem Command Set Below are modem commands that can be used with AT (Hayes) compatible modems. All commands are used with the 'AT' prefix. For example, to manually set the speaker volume to medium, the ATL2 command would be entered in a communications program (such as Terminal or HyperTerminal). In these commands "n" signifies a number (see below) NOTE: These are general modem commands. Certain commands may not work with all modems. Consult the documentation for your modem if you experience difficulties, or contact your modem manufacturer’s technical support department. AT Command Reference%Cn : Enable/Disable Data Compression %En : Auto-Retrain control &Cn : DCD Control &Dn : DTR Option &Fn : Recall Factory Profile &Gn : Select Guard Tone &Jn : Telephone Jack Control &Kn : Data Flow Control &Qn : Communication (Sync/Async Mode) &Rn : RTS/CTS (Hardware) Flow Control &Tn : Test Mode &V: View Configuration &Wn : Store User Profile &Yn : Default User Profile )Mn : Cellular Power Level Adjustment *Hn : Link Negotiation Speed +++ : Escape Sequence +MS : Select Modulation :En : Compromise Equalizer Setting ? : Read Currently Selected S Register @Mn : Initial Cellular Power Level Setting \An : Select Maximum MNP Block Size \Bn : Transmit Break \Gn : Modem to Modem (Software) Flow Control \Ln : Select MNP Block/Stream Mode \Nn : Protocol Negotiation Selection A : Answer A/: Re-execute Command Bn: CCITT or Bell Selection Cn: Carrier Control Dn: Dial En: Command Echo Fn: Select Modulation Hn: Disconnect (Hang-up) In: Identification Ln: Speaker Volume Mn: Speaker Control Nn: Automode Enable (Automatic Line Speed Detection) On: Return to Online Data Mode P : Set Pulse Dial Default Qn: Result Code On/Off Sn: Select a Specific S Register Sn? : Read an S Register T : Set Tone Dial Default Vn: Result Code Format Wn: Negotiation Progress (Connect Message) Control Xn: Extended Result Code Yn: Long Space Disconnect Zn: Modem Reset Sn=x: Write an S Register Value &Zn=x : Store Phone Number MORE INFORMATION &F0 -- Recall Factory Profile 0. Factory Profile 0 contains the default values from the modem chipset supplier. &F1 -- Recall Factory Profile 1. Factory Profile 1 contains the default values defined by the product manufacturer. &Jn (Telephone Jack Control) This command is only included for compatibility and performs no function. The value is written into S-Register 21. &V (View Configuration) This command displays the current active configuration, stored user profiles, and the first four stored telephone numbers. &Wn (Store User Profile) This command stores the current, active configuration including S- Registers into non-volatile memory as stored user's profile 0 or 1. Storable parameters can be viewed by &V command. Stored parameters can be recalled into active configuration by Zn command or at power on. &W0 Store active configuration as user's profile 0. &W1 Store active configuration as user's profile 1. &Yn (Default User Profile) This command selects which of two user's profiles will be loaded into the active configuration following Power on Reset. &Y0 -- Selects power up configuration as user's profile 0. &Y1 -- Selects power up configuration as user's profile 1. &Cn (DCD Control) This command controls the behavior of the DCD (Data Carrier Detect) signal of the internal serial port. &C0 : DCD is always on. &C1 : DCD will track the state of the data carrier from the remote modem. &Dn (DTR Option) This command controls the modem response to the serial port's Data Terminal Ready (DTR) signal. This command interprets the ON and OFF transitions of the DTR signal from the DTE in accordance with the parameters as defined by n. E0 : Inhibits the command echo. E1 : Enables the command echo. Qn (Result Code On/Off) Used to enable and disable return results codes to the DTE. Q0 : Enable the result code. Q1 : Disable the result code, OK, ERROR or CONNECT message will not be returned. Vn (Result Code Format) This command determines the format of the return result code if result codes are enabled. V0 : Selects result codes in NUMERIC format. V1 : Selects result codes in WORD format. The following command controls the modem speaker volume when the speaker is turned on. L0,1 : Selects low speaker volume. L2 : Selects medium speaker volume. L3 : Selects high speaker volume. Mn : (Speaker Control) This command selects when the modem speaker will be on or off. M0 : The speaker is always off. M1 : Enables the speaker during call establishment, but off after the carrier is detected. M2 : The speaker is always on. M3 : Disables the speaker during the dialling period and receiving carrier, but on during answering. |
|||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||